AP5100WG-7

Diodes Incorporated
621-AP5100WG-7
AP5100WG-7

メーカ:

詳細:
スイッチング電圧レギュレータ 1.2A Step-Down Conv 1.4MHz Sw Freq

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫: 169,035

在庫:
169,035 すぐに出荷可能
工場リードタイム:
24 週間 表示されている時間を超える工場生産予定時間。
この製品はリードタイムが長いと報告されています。
最小: 1   倍数: 1
ユニット価格:
¥-
合計 額:
¥-
EST関税:
パッケージング:
完全リール(3000の倍数で注文)

価格 (JPY)

数量 ユニット価格
合計 額
カットテープ/ MouseReel™
¥96 ¥96
¥68.6 ¥686
完全リール(3000の倍数で注文)
¥68.6 ¥205,800
† ¥750 MouseReel™の料金が追加され、ショッピングカートに加算されます。すべてのMouseReel™の注文は、キャンセルおよび返品できません。

製品属性 属性値 属性の選択
Diodes Incorporated
製品カテゴリー: スイッチング電圧レギュレータ
RoHS:  
SMD/SMT
SOT-26-6
Buck
800 mV to 15 V
1.2 A
1 Output
4.75 V
24 V
400 uA
1.4 MHz
- 25 C
+ 85 C
AP5100
Reel
Cut Tape
MouseReel
ブランド: Diodes Incorporated
製品タイプ: Switching Voltage Regulators
工場パックの数量: 3000
サブカテゴリ: PMIC - Power Management ICs
タイプ: Voltage Converter
単位重量: 15 mg
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

JPHTS:
8542390990
CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390090
TARIC:
8542399000
MXHTS:
8542399999
ECCN:
EAR99

AP5100 Step-Down Converter

Diodes Incorporated AP5100 current mode step-down converter with built-in power MOSFET enables the smallest solution size power conversion. With the low series resistance power switch the Diodes Incorporated AP5100 step-down converter enables a constant output current of up to 1.2A over a wide input supply range. The load and line regulation has excellent response time over the operating input voltage and temperature range. 

PAM2306 Dual Step-Down DC-DC Converters

Diodes Incorporated offers a wide range of non-isolated DC-DC Converters. These switching voltage regulator converters feature integrated power switches to make designing easier and to minimize component count. With internal or external compensation, the designer can opt for smaller board space and fewer components or select specific inductor and capacitor values. Higher switching frequencies reduce the output ripple current and allow for comparatively smaller inductors (although special attention has to be given to EMI). Overcurrent, overvoltage, and overtemperature protection increase board reliability and prevent premature failures. A Power Good signal, in combination with an Enable pin, can be used for power sequencing and can warn the processor of possible supply problems and shut down in a controller manner. DC-DC converters include buck, boost, buck/boost, external buck, and external boost.